include <helpers.scad>

// m12 female body connector for soldering

// female
// inner thick part length includes rubber o-ring,
// outer does not
m12_female_conn_body_thick_part_length = 3.6;
m12_female_conn_body_thick_part_d = 18;

m12_female_conn_body_outer_part_length = 16;
m12_female_conn_body_outer_part_d = 15.1;
m12_female_conn_body_outer_part_flat_w = 13.4;

m12_female_conn_body_wires_length = 20;
m12_female_conn_body_wires_d = 8;

// male
m12_male_conn_body_thick_part_length = 3.6;
m12_male_conn_body_thick_part_d = 18;

m12_male_conn_body_outer_part_length = 16;
m12_male_conn_body_outer_part_d = 12;
m12_male_conn_body_outer_part_flat_w = 10.6;

m12_male_conn_body_wires_length = 20;
m12_male_conn_body_wires_d = 8;

// wl - wires length
// wd - wires diameter
// tcl - inner (thick) part length
// tcd - inner (thick) part diameter
// ocl - outer connector length
// ocd - outer connector diameter
// ocfw - outer connector flat width
module m12_connector(
    wl,
    wd,
    tcl,
    tcd,
    ocl,
    ocd,
    ocfw,
)
{
    rotate([90, 0, 0])
    {
        // thick connector part inside scanner body
        translate([0, 0, -tcl])
        cylinder($fn = dToFn(tcd), d = tcd, h = tcl);
        
        // outer connector part going outside through
        // scanned body
        cylinder($fn = dToFn(ocd), d = ocd, h = ocl);
        
        // soldered wires
        translate([0, 0, -wl - tcl + wd / 2])
        cylinder($fn = dToFn(wd), d = wd, h = wl);
        
        translate([0, 0, -wl -tcl + wd / 2])
        sphere($fn = dToFn(wd), d = wd);
    }
}

module m12_female_conn_body()
{
    wl = m12_female_conn_body_wires_length;
    wd = m12_female_conn_body_wires_d;
    
    tcl = m12_female_conn_body_thick_part_length;
    tcd = m12_female_conn_body_thick_part_d;
    
    ocl = m12_female_conn_body_outer_part_length;
    ocd = m12_female_conn_body_outer_part_d;
    ocfw = m12_female_conn_body_outer_part_flat_w;
    
    rotate([90, 0, 0])
    {
        // thick connector part inside scanner body
        translate([0, 0, -tcl])
        cylinder($fn = dToFn(tcd), d = tcd, h = tcl);
        
        // outer connector part going outside through
        // scanned body
        cylinder($fn = dToFn(ocd), d = ocd, h = ocl);
        
        // soldered wires
        translate([0, 0, -wl - tcl + wd / 2])
        cylinder($fn = dToFn(wd), d = wd, h = wl);
        
        translate([0, 0, -wl -tcl + wd / 2])
        sphere($fn = dToFn(wd), d = wd);
    }
}

module m12_female_connector()
{
    m12_connector(
        m12_female_conn_body_wires_length,
        m12_female_conn_body_wires_d,
        
        m12_female_conn_body_thick_part_length,
        m12_female_conn_body_thick_part_d,
        
        m12_female_conn_body_outer_part_length,
        m12_female_conn_body_outer_part_d,
        m12_female_conn_body_outer_part_flat_w
    );
}

module m12_male_connector()
{
    m12_connector(
        m12_male_conn_body_wires_length,
        m12_male_conn_body_wires_d,
        
        m12_male_conn_body_thick_part_length,
        m12_male_conn_body_thick_part_d,
        
        m12_male_conn_body_outer_part_length,
        m12_male_conn_body_outer_part_d,
        m12_male_conn_body_outer_part_flat_w
    );
}